The base of the phone's front face, where you put your ear, is usually always where you'll find the ear speakers.
- Alternative speaker positions include the side next to the volume button and the bottom of the device's front face. Take note of these locations.
- To get rid of any more junk, you might wish to clean your phone's screen first.
Step 2: Use a cotton swab to rub the outsides of your phone speaker. Apply some pressure as you move a cotton swab lightly in a circular manner over your speaker holes. Continue doing this until all of the dirt has been removed. Press the cotton swab into the speaker holes if they are large enough. But only enough pressure should be applied so that the cotton swab, just at tip, fits into the slot. Once within, apply a little pressure and rub the cotton swab left to right.
- When a cotton swab accumulates the dirt, replace them.
- Apply a small bit of rubbing alcohol on your cotton swab for improved results.
Step 3: Make a tiny ball out of sticky tack and place it over the speaker openings. Squeeze a piece of sticky tack that is 1 inch (2.5 cm) long into a ball. Compress it continuously until it becomes flexible and soft. Then, firmly press it into the speaker holes. Put enough force on the adhesive tack so that it enters the speaker. Remove it after holding it in place for two to three seconds; dirt should be adhered to the sticky tack. Repeat this procedure until no more dirt is seen coming from the speakers.
- Make sure you're always using the clean surface of your sticky tack by moving it around.
- Shop for sticky tack online or at office supply stores.
Step 4: Small speaker grills should be cleaned with a medium-bristle toothbrush. Place the brush with the top or bottom of your phone in mind. Move it up and down while keeping it aligned to the top of your phone. After that, clean by sliding your toothbrush left and right while holding it parallel to the surface of your phone.
- For tough dirt, tilt the brush upward and scrape with the bottom bristles.
- Always use a medium-bristled brush; softer bristles can't effectively remove dirt, and thicker bristles can't fit through the tiny speaker holes.
Method 2: How to Clean Phone Speaker Using Compressed Air
Step 1: Get yourself a can of compressed air. Electronics retailers, office supply stores, and online providers all carry compressed air cans. Try it out by squeezing the nozzle down while pointing it downward. Get a sense of how much air each spray emits.
- To boost accuracy, get a can with a straw.
- This is a fantastic technique to clean a TV screen as well.
Step 2: To increase precision, attach the straw to the can's nozzle. Attach a tiny straw to the compressed air can nozzle using the screwdriver. Try it out by squeezing the nozzle down while pointing it downward. The straw's tip needs to be where the air is to be released.
- If you notice air escaping the edges of the nozzle as you spray, tighten the straw.
- If you feel confident shooting your pressurised air without it, remove the straw.
Step 3: In three to four brief bursts, blow compressed air into the speaker slot. Maintain a distance of at least 12 inch (1.3 cm) between the straw's nozzle or tip and the speaker aperture. This will get rid of extra dirt from your cotton swab that was squeezed into the speaker.
- Avoid blowing too closely to the speaker to prevent electrical damage to the phone's internal parts.
- If you're using a straw, maintain it steady while blowing air by holding it in your non-dominant hand.
Method 3: How to Clean Phone Speaker from the Insides
Step 1: Your phone's back lid can be removed using a spudger and suction cup. Wondering how to clean my phone speaker from the insides? Use a hairdryer on low heat for around 15 seconds to warm the phone's edge. Apply a suction cup to the rear after that. Pull the suction lever slowly in your direction while the screen is facing downward. Put a spudger's flat end between the perimeter aperture and lever that towards you at the same time. Lever the back piece until it pops off by continuing to tug on the suction cup.
- Home hardware stores sell spudgers, a tool with a broad flat-head screwdriver tip that doubles as a wedge.
- Apply extra heat to the edge if you're having problems to melt the adhesive keeping the two phone pieces together.
- You can take the back off of older, less expensive phone models using your hands. This is not viable for more recent, pricey smartphones with glass backs.
Step 2: Take off the metal covers that are covering the speakers. Usually, metal covers keep the phone's speakers and earphones in place. By using a screwdriver, get rid of the screws keeping the covers on. Next, gently remove the speakers.
- If you're having problems, use a spudger to carefully remove the speakers.
Step 3: Use a microfiber cloth soaked in rubbing alcohol to clean the speakers. Rub some rubbing alcohol in a thin layer onto a soft microfiber. Cleanse the speaker components by gently scrubbing them. Blow softly into the apertures from the outside. After that, carefully rub the speaker apertures with a cotton swab that has been dipped in alcohol.
- A soft rag or lint-free towel are other options. They are less successful at picking up dirt, though.
- Before placing your speaker back together, make sure the speakers and openings have had time to dry.
Step 4: If you are still unable to access your speakers, detach the second back piece. To access the speaker apertures on some phones, usually Samsung brands, you must remove a second rear piece. Although the precise number differs by model and manufacturer, there will be an additional 10 to 13 screws to remove from these phones. Each screw should be turned anticlockwise with a 4 inch screwdriver until it comes loose. Pull the second back piece off after that.
Method 4: How to Clean Phone Speaker Using Silica Gel
Step 1: Switch your phone off. In case you have spilt water on your phone, you should first switch off your phone before attempting to know how to clean my phone speaker. Turning off your gadget as soon as you can is necessary.
Step 2: Use a towel to dry the phone. The phone should be secure to handle as long as it is off. Make sure to properly dry the outside.
- Make sure to remove the battery and SIM card from your Android cellphone if you can.
Step 3: Put silica gel packs in a sealed plastic bag with the phone inside. You can buy silica gel packs online or discover some in packaging lying about your home. These little white packs typically have the phrase "Do not eat" printed on them.
- If you do not have any silica gel packets, you can use another drying agent or dry, uncooked rice in its place.
Step 4: Give the phone at least a day in the bag. The greatest location is one that receives some sunlight because it will aid in removing the moisture from the phone.
- Don't leave your phone in the sun for an extended period of time.
- You can take the device out after the bag is free of condensation.
Step 5: Switch your phone on. You can turn on your phone after checking for any traces of water.
Method 5: How to Clean Phone Speaker by Playing a Video
Step 1: Make sure your device has been fully dried. If you respond immediately and use a desiccant, you can rescue a wet phone.
- If your speaker has water in it and the charging port is not broken, use this approach.
- The sound waves produced by the tones can cause your gadget to discharge water.
Step 2: Launch your mobile browser and play the tone video. It might launch immediately on the YouTube app if you have one.
Step 3: Play the video. Make sure the volume on your device is at its highest setting. This will guarantee that the tones are played correctly and provide the sound waves required to force the water out.
Step 4: If necessary, repeat. During playback, you might need to reposition the device. To guarantee that water exits your device, keep the holes of the speakers facing down at all times.
